1. Start and start correctly

發動機冷車起動時，因?yàn)闇囟鹊?，機油粘度大，流動性差，使機油泵供油缺乏。同時，原氣缸壁上的機油在停車后沿氣缸壁下賤，因而在起動的瞬間得不到正常作業時那樣杰出的光滑，致使起動時氣缸璧磨損大大增加。

When the engine starts cold, the oil pump is short of oil supply because of low temperature, high oil viscosity and poor fluidity. At the same time, the oil on the cylinder wall of the original gas drops down along the cylinder wall after stopping, so it can't get the excellent smoothness at the moment of starting, which greatly increases the wear of the cylinder wall during starting.

因而，初次起動時，應先使發動機空轉幾圈，待摩擦表面得到光滑后再起動。起動后應怠速運轉升溫，嚴禁猛轟油口，待機油溫度達到40℃時再起步；起步應堅持掛低速檔，并循序每一檔位行駛一段里程，直到油溫正常，方可轉為正常行駛。

Therefore, when starting the engine for the first time, it is necessary to make the engine idle for several circles and wait until the friction surface is smooth before starting. After starting, the engine should run at idle speed to raise the temperature. It is strictly forbidden to bang the oil port. When the oil temperature reaches 40 ℃, the engine should start again. When starting, the engine should stick to the low gear, and drive a section of mileage in each gear step by step until the oil temperature is normal.

2.正確選用光滑油

2. Choose smooth oil correctly

要嚴厲按季節和發動機功能要求選用較佳粘度值的光滑油，不行隨意購用殘次光滑油，并常常查看和堅持光滑油的數量與質量。

It is necessary to strictly select the smooth oil with better viscosity according to the requirements of season and engine function. It is not allowed to purchase defective smooth oil at will. It is also necessary to check and insist on the quantity and quality of smooth oil.

3.加強濾清器的保養

3. Strengthen the maintenance of filter

使空氣濾清器、機油濾清器和燃油濾清器堅持杰出的作業狀態，對減輕氣缸套的磨損至關重要。加強對“三濾”的保養，是避免機械雜質進入氣缸，減輕氣缸磨損，延長發動機使用壽命的一項重要措施，在農村和多風沙區域尤為重要。有的駕駛員為了節省燃料而不裝空氣濾清器是肯定過錯的。

Keeping the air filter, oil filter and fuel filter in excellent working condition is very important to reduce the wear of cylinder liner. Strengthening the maintenance of the "three filters" is an important measure to prevent mechanical impurities from entering the cylinder, reduce cylinder wear and prolong the service life of the engine, especially in rural areas and windy and sandy areas. It is definitely wrong for some drivers not to install air filters in order to save fuel.

4.堅持發動機正常作業溫度

4. Adhere to the normal operating temperature of the engine

發動機的正常作業溫度應處在80-90℃。溫度過低，不能堅持杰出的光滑，會增大氣缸壁的磨損，氣缸內的水蒸氣易凝結成水珠，溶解廢氣中的酸性氣體分子，生成酸性物質，使氣缸璧遭到腐蝕磨損。

The normal operating temperature of the engine should be 80-90 ℃. If the temperature is too low, it will increase the wear of the cylinder wall. The water vapor in the cylinder is easy to condense into water droplets, dissolve the acid gas molecules in the exhaust gas, and generate acid substances, which will cause corrosion and wear of the cylinder wall.

試驗標明，當氣缸璧溫度由90℃降到50℃時，氣缸磨損量為90℃時的4倍。溫度過高，會使氣缸強度降低而加重磨損，乃至可能使活塞過度脹大而形成“脹缸”事端。

The test shows that when the cylinder wall temperature drops from 90 ℃ to 50 ℃, the wear loss of the cylinder is four times of that of 90 ℃. If the temperature is too high, the strength of the cylinder will be reduced and the wear will be aggravated, and even the piston may be over inflated, resulting in "cylinder expansion".

5.提高保修質量

5. Improve warranty quality

在使用過程中，及時發現問題及時予以排除，隨時更換或維修損壞和變形的配件。裝置氣缸套時要嚴厲按技術要求檢驗和裝配。

In the process of use, timely find out problems and eliminate them, and replace or repair damaged and deformed parts at any time. The cylinder liner should be inspected and assembled strictly according to the technical requirements.

在保修換環作業中，要選用彈力適當?shù)幕钊h(huán)，彈力過小，使燃?xì)飧Z入曲軸箱吹落氣缸壁上的機油，增大氣缸壁磨損；彈力過大，直接加重氣缸壁的磨損，或因氣缸壁上的油膜遭到損壞而加重其磨損。

In the operation of ring replacement under warranty, the piston ring with proper elastic force should be selected. If the elastic force is too small, the gas will flow into the crankcase and blow off the oil on the cylinder wall, which will increase the wear of the cylinder wall. If the elastic force is too large, the wear of the cylinder wall will be directly aggravated, or the wear will be aggravated due to the damage of the oil film on the cylinder wall.

以上信息是我們濟南奔馳汽車維修哪家好整理發布希望對大家有所幫助，我們的網站是：http://m.gxnn10z.com！

The above information is our Jinan Benz car repair which good collation release, I hope to help you, our website is: http://m.gxnn10z.com !